- Spyder 4 elite pro install#
- Spyder 4 elite pro update#
- Spyder 4 elite pro pro#
- Spyder 4 elite pro software#
The Software is protected under the copyright law of Japan and other countries, and related Conventions.
Spyder 4 elite pro update#
The Software also includes the associated materials, and any modification, upgrade and update of the Software granted to You by JKC.Įnd-User ("You") acknowledge that all copyrights and other intellectual property rights in the Software is owned by JKC and its licensor, and remain vested in JKC and such licensor. HOWEVER, INSTALLING OR USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS.
Spyder 4 elite pro install#
If You do not agree to the terms of the Agreement, you may not install the Software any more. The right to use the Software is granted by JVCKENWOOD Corporation("JKC") to You only on the condition that You agree to the following Agreement.
Spyder 4 elite pro pro#
if you don't need the extra analysis reports of the Elite or a specific module to target white and/or black luminance and a real time meter from the puck sensor, the Pro looks very good as it is also capable of calibrating multiple monitors.Please carefully read this End-User License Agreement ("Agreement") before installing or using the "Driver software" ("Software") on your PC. This is much better than what Spyder 3 Pro user's had advised to me last year - where you did not get a readout from the sensor until the summary screen of the calibration, forcing you to go back through the entire calibration to reset the brightness. (I hope to have a screen capture to insert here shortly) In the Pro version you still cannot manually key in a desired target value.Īt this point you can also adjust your brightness control and then "update" to refresh the read out from the puck sensor. I believe the "Target" value comes from the Ambient Light sensor of the Spyder4 - it is the value that it suggests after sampling your ambient light. In Advanced mode (I think it is still called this) early in the calibration cycle when you are in the Color Temperature screen where you have the a meter showing the RGB levels and are tweaking your RGB sliders to get to a Kelvin point, it ALSO shows you the Target White Luminance value and your ACTUAL White Luminance value. I just learned from a Spyder 4 Pro user a few things. So basically I want the lowest cost solution that will make my monitor match my SmugMug calibration prints I've got (either with my current monitor - Samsung P2250 - or the ASUS monitor we talked about in the other thread, or another IPS panel). But worse is paying for solutions that don't solve the problem. I'm just an amateur shooter, but I'm also tired of too dark prints with dodgy colors, so I'm looking for a calibrated monitor solution that doesn't bust the bank. So what else would make the Elite more useable in the real world? What about the gamma and color temp choices - are those actually useful or just gimmicks?Īs you can maybe tell from this and my monitor thread, I don't have an unlimited budget for this stuff (did I mention my daughter owns a horse?).
But I'm having trouble justifying going from $115 (for the Express) to the Elite (more than double at $250) based on that alone. I like that the Elite has the simpler - and more accurate - luminance controls. If the S4 is just a carry over, this is what you will get. In your "Monitors" thread I strongly encouraged you to consider the Elite. You don't have to wait until the end of the calibration to learn the value of your luminance.įurthermore, I believe the Elite has some features that help to speed up calibrating a system with two or more monitors. Once set you move on with the RGB part of the calibration. You will adjust your Brightness, check the real time reading, and adjust again if necessary. The Spyder software will then use the puck to sample the screen and you will be given a real time meter showing the current white luminance value. You will have to enable "Measured Luminance" in the software and then proceed with the calibration.
The Elite will give you a dedicated module for setting the white and black luminance. If you are not happy with this luminance value you will have to redo the entire calibration to get around to seeing what the new tweaked value is. At the end of the calibration, and only then, you will be given the white luminance value on the final report page. The Spyder software will present a screen with a gray scale like set of objects in which you will have to eyeball increasing or decreasing the brightness so that you see the squares. It will use the puck to sample but setting the level is by eyeball. Here's my understanding of the Pro's functionality to measure luminance and this is based on the software found in the Spyder3. My question is whether I would ever need the extra features of the pro, and whether it's worth the extra $50.